diff --git a/boneio-dimmer_gen2_8ch-dev0_4.yaml b/boneio-dimmer_gen2_8ch-dev0_4.yaml
index 98d7565..69ccd60 100644
--- a/boneio-dimmer_gen2_8ch-dev0_4.yaml
+++ b/boneio-dimmer_gen2_8ch-dev0_4.yaml
@@ -123,7 +123,7 @@ packages:
       - path: sdm630.yaml
 
 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-dimmer_g2_8ch-dev0_4.yaml@main
+  package_import_url: github://boneIO-eu/esphome/boneio-dimmer_gen2_8ch-dev0_4.yaml@main
   import_full_config: true
 
 pcf8574:
diff --git a/boneio-dimmer_gen2_8ch-v0_1.yaml b/boneio-dimmer_gen2_8ch-v0_1.yaml
new file mode 100644
index 0000000..98c5ba5
--- /dev/null
+++ b/boneio-dimmer_gen2_8ch-v0_1.yaml
@@ -0,0 +1,374 @@
+substitutions:
+  name: boneio-dr-gen2-8ch-01
+  friendly_name: 'BoneIO Dimmer 8ch'
+  serial_prefix: 'dim2' #Don't change it.
+  firmware_manifest: 'https://boneio.eu/fwesp/boneio-dr-gen2-8ch-01.json'
+esphome:
+  name: '${name}'
+  friendly_name: '${friendly_name}'
+  name_add_mac_suffix: true
+  project:
+    name: boneio.dimmer-led-gen2
+    version: '0.1'
+  on_boot:
+    priority: -100
+    then:
+      - delay: 5s
+      - if:
+          condition:
+            lambda: 'return id(serial_no) != nullptr;'
+          then:
+            - component.update: serial_no
+            - logger.log: "Serial No updated on boot"
+          else:
+            - logger.log: "Serial No component not found"
+
+esp32:
+  board: esp32-s3-devkitc-1
+  framework:                                                                            
+    type: esp-idf
+
+ethernet:
+  id: eth
+  type: W5500
+  clk_pin: GPIO13
+  mosi_pin: GPIO39
+  miso_pin: GPIO38
+  cs_pin: GPIO12
+  interrupt_pin: GPIO2
+  reset_pin: GPIO1
+  clock_speed: 25MHz
+
+external_components:
+  - source: github://boneIO-eu/esphome-LM75@main #Original source and thank you note for BTomala https://github.com/boneIO-eu/esphome-lm75
+    components: [lm75]
+
+i2c:
+  sda: GPIO10
+  scl: GPIO11
+  scan: True
+  frequency: 400kHz
+
+uart:
+  id: boneio_uart
+  rx_pin: GPIO21
+  tx_pin: GPIO14
+  baud_rate: 9600
+  stop_bits: 1
+
+output:
+  - platform: ledc
+    pin: GPIO18
+    frequency: 1000Hz
+    inverted: false
+    id: chl01
+  - platform: ledc
+    pin: GPIO17
+    frequency: 1000Hz
+    inverted: false
+    id: chl02
+  - platform: ledc
+    pin: GPIO16
+    frequency: 1000Hz
+    inverted: false
+    id: chl03
+  - platform: ledc
+    pin: GPIO15
+    frequency: 1000Hz
+    inverted: false
+    id: chl04
+
+  - platform: ledc
+    pin: GPIO7
+    frequency: 1000Hz
+    inverted: false
+    id: chr01
+  - platform: ledc
+    pin: GPIO6
+    frequency: 1000Hz
+    inverted: false
+    id: chr02
+  - platform: ledc
+    pin: GPIO5
+    frequency: 1000Hz
+    inverted: false
+    id: chr03
+  - platform: ledc
+    pin: GPIO4
+    frequency: 1000Hz
+    inverted: false
+    id: chr04
+
+
+  ##CAN gpio48 - tx, gpio47 rx, gpio35 stb
+
+modbus:
+  send_wait_time: 80ms
+  uart_id: boneio_uart
+  id: boneio_modbus
+
+packages:
+  internals_packages:
+    url: https://github.com/boneIO-eu/esphome
+    ref: v1.7.1
+    files: [
+        'devices/serial_no.yaml',
+        # 'devices/dimmer_i2c.yaml',
+      ]
+  boneiopackages:
+    url: https://github.com/boneIO-eu/esphome_packages
+    ref: main
+    refresh: 1min
+    files:
+      - path: sdm630.yaml
+
+dashboard_import:
+  package_import_url: github://boneIO-eu/esphome/boneio-dimmer_gen2_8ch-v0_1.yaml@main
+  import_full_config: true
+
+pcf8574:
+  - id: 'pcf_inputs'
+    address: 0x38
+
+# http_request:
+#   timeout: 7s
+#   verify_ssl: false
+logger:
+  hardware_uart: UART0
+api:
+  reboot_timeout: 0s
+ota:
+  - platform: esphome
+  - platform: web_server
+  # - platform: http_request
+
+# update:
+#   - id: update_std
+#     platform: http_request
+#     name: boneIO FW Update
+#     update_interval: 3 minutes
+#     source: ${firmware_manifest}
+
+web_server:
+  port: 80
+  version: 3
+  local: true
+
+
+light:
+  - platform: monochromatic
+    output: chl01
+    name: 'CHL 01'
+    id: chl_01
+    default_transition_length: 2s
+    gamma_correct: 0
+  - platform: monochromatic
+    output: chl02
+    name: 'CHL 02'
+    id: chl_02
+    default_transition_length: 2s
+    gamma_correct: 0
+  - platform: monochromatic
+    output: chl03
+    name: 'CHL 03'
+    id: chl_03
+    default_transition_length: 2s
+    gamma_correct: 0
+  - platform: monochromatic
+    output: chl04
+    name: 'CHL 04'
+    id: chl_04
+    default_transition_length: 2s
+    gamma_correct: 0
+
+  - platform: monochromatic
+    output: chr01
+    name: 'CHR 01'
+    id: chr_01
+    default_transition_length: 2s
+    gamma_correct: 0
+  - platform: monochromatic
+    output: chr02
+    name: 'CHR 02'
+    id: chr_02
+    default_transition_length: 2s
+    gamma_correct: 0
+  - platform: monochromatic
+    output: chr03
+    name: 'CHR 03'
+    id: chr_03
+    default_transition_length: 2s
+    gamma_correct: 0
+  - platform: monochromatic
+    output: chr04
+    name: 'CHR 04'
+    id: chr_04
+    default_transition_length: 2s
+    gamma_correct: 0
+
+debug:
+  update_interval: 15s
+
+sensor:
+  - platform: debug
+    free:
+      name: "Heap Free"
+    block:
+      name: "Heap Max Block"
+    loop_time:
+      name: "Loop Time"
+  - platform: lm75
+    id: boneIO_temp
+    name: 'Temperature'
+    update_interval: 30s
+    entity_category: diagnostic
+    on_value_range:
+      - above: 70.0
+        then:
+          - switch.turn_on: buzzer
+      - below: 70.0
+        then:
+          - switch.turn_off: buzzer
+
+switch:
+  - platform: gpio
+    id: buzzer
+    name: 'Buzzer'
+    pin:
+      number: GPIO9
+      mode:
+        output: true
+      inverted: false
+  - platform: gpio
+    id: can_bus_switch
+    name: 'CAN Bus Switch'
+    pin:
+      number: GPIO35
+      mode:
+        output: true
+      inverted: false
+  - platform: gpio
+    name: "CAN RX"
+    pin: GPIO47
+  - platform: gpio
+    name: "CAN TX"
+    pin: GPIO48
+
+binary_sensor:
+
+  - platform: gpio
+    name: 'IN_01'
+    id: in_01
+    pin:
+      pcf8574: pcf_inputs
+      number: 0
+      mode:
+        input: true
+      inverted: true
+
+  - platform: gpio
+    name: 'IN_02'
+    id: in_02
+    pin:
+      pcf8574: pcf_inputs
+      number: 1
+      mode:
+        input: true
+      inverted: true
+
+  - platform: gpio
+    name: 'IN_03'
+    id: in_03
+    pin:
+      pcf8574: pcf_inputs
+      number: 2
+      mode:
+        input: true
+      inverted: true
+
+  - platform: gpio
+    name: 'IN_04'
+    id: in_04
+    pin:
+      pcf8574: pcf_inputs
+      number: 3
+      mode:
+        input: true
+      inverted: true
+
+  - platform: gpio
+    name: 'IN_05'
+    id: in_05
+    pin:
+      pcf8574: pcf_inputs
+      number: 4
+      mode:
+        input: true
+      inverted: true
+
+  - platform: gpio
+    name: 'IN_06'
+    id: in_06
+    pin:
+      pcf8574: pcf_inputs
+      number: 5
+      mode:
+        input: true
+      inverted: true
+
+  - platform: gpio
+    name: 'IN_07'
+    id: in_07
+    pin:
+      pcf8574: pcf_inputs
+      number: 6
+      mode:
+        input: true
+      inverted: true
+
+  - platform: gpio
+    name: 'IN_08'
+    id: in_08
+    pin:
+      pcf8574: pcf_inputs
+      number: 7
+      mode:
+        input: true
+      inverted: true
+  - platform: template
+    name: CAN Bus Button
+    id: can_bus_button
+
+
+# canbus:
+#   - platform: esp32_can
+#     tx_pin: GPIO48
+#     rx_pin: GPIO47
+#     can_id: 4
+#     bit_rate: 50kbps
+#     on_frame:
+#       - can_id: 5
+#         then:
+#           - lambda: |-
+#               if(x.size() > 0) {
+#                 switch(x[0]) {
+#                   case 0x12:  // button release
+#                     id(can_bus_button).publish_state(false);
+#                     break;
+#                   case 0x11:  // button press
+#                     id(can_bus_button).publish_state(true);
+#                     break;
+#                 }
+#               }
+
+# button:
+#   - platform: template
+#     name: 'CAN Sensor ON'
+#     on_press:
+#       - logger.log: Button Pressed
+#       - canbus.send: [0x11, 0x22, 0x33]
+#   - platform: template
+#     name: 'CAN Sensor OFF'
+#     on_press:
+#       - logger.log: Button Pressed
+#       - canbus.send: [0x12, 0x22, 0x33]
\ No newline at end of file