add first test esphome yaml config

test_esplan.yaml

@@ -0,0 +1,180 @@
+substitutions:
+  devicename: wt32
+  
+esphome:
+  name: ${devicename}
+  platform: ESP32
+  board: esp-wrover-kit
+  on_boot:
+    then:
+      ds1307.read_time:
+
+
+ethernet:
+  type: LAN8720
+  mdc_pin: GPIO23
+  mdio_pin: GPIO18
+  clk_mode: GPIO0_IN
+  phy_addr: 1
+  power_pin: GPIO16
+  id: eth
+
+external_components:
+  - source: github://ell249/esphome-PCT2075@master
+    components: [ pct2075 ]
+  - source: github://btomala/esphome-LM75@v1
+    components: [ lm75 ]
+
+font:
+  - file: "fonts/DejaVuSans.ttf"
+    id: fontSmall
+    size: 9
+  - file: "fonts/danube__.ttf"
+    id: danube
+    size: 15
+
+logger:
+  level: DEBUG
+  baud_rate: 0 #Important. You can't use serial port
+
+api:
+ota:
+
+web_server:
+  port: 80
+
+i2c:
+  - id: bus_b
+    sda: 14
+    scl: 15
+    scan: true
+
+time:
+  - platform: ds1307
+    update_interval: never
+  - platform: homeassistant
+    on_time_sync:
+      then:
+        ds1307.write_time:
+
+
+display:
+  - platform: ssd1306_i2c
+    model: "SH1106 128x64"
+    address: 0x3C
+    id: my_display
+    pages:
+      - id: page1
+        lambda: |-
+          it.print(3, 3, id(danube), "bone");
+          it.print(53, 3, id(danube), "iO");
+          it.print(3, 22, id(fontSmall), "Host: ${devicename}");
+          int seconds = round(id(uptime_sensor).raw_state);
+          int days = seconds / (24 * 3600);
+          seconds = seconds % (24 * 3600);
+          int hours = seconds / 3600;
+          seconds = seconds % 3600;
+          int minutes = seconds /  60;
+          seconds = seconds % 60;
+          it.printf(3, 32, id(fontSmall), "IP Address: 192.168.1.1");
+          it.printf(3, 42, id(fontSmall), "Uptime: %s", (
+            (days ? to_string(days) + "d " : "") +
+            (hours ? to_string(hours) + "h " : "") +
+            (minutes ? to_string(minutes) + "m " : "") +
+            (to_string(seconds) + "s")
+          ).c_str());
+      - id: page2
+        lambda: |-
+          it.printf(0, 0, id(fontSmall), "MCP1_1: %s", id(switch_mcp_out1_1).state ? "ON" : "OFF");
+          it.print(0, 10, id(fontSmall), "This is page 2!");
+sensor:
+  - platform: mcp9808
+    name: "Living Room Temperature"
+    update_interval: 60s
+  - platform: uptime
+    id: uptime_sensor
+  - platform: lm75
+    id: temperature
+    name: "Board temperature measurement"
+    update_interval: 60s
+    address: 0x48
+# sensor:
+          # it.printf(3, 32, id(fontSmall), "Wi-Fi: %.1s", id(eth).state);
+#   - platform: pct2075
+#     address: 0x18
+#     temperature:
+#       name: "PCT2075 Temperature"
+#     update_interval: 30s
+
+
+mcp23017:
+  - id: 'mcp23017_out1'
+    address: 0x20
+  - id: 'mcp23017_out2'
+    address: 0x21
+  - id: 'mcp23017_out3'
+    address: 0x22
+  - id: 'mcp23017_out4'
+    address: 0x23
+
+# # Individual outputs
+switch:
+  - platform: gpio
+    id: switch_mcp_out1_1
+    name: "MCP23017 Pin A0"
+    pin:
+      mcp23xxx: mcp23017_out1
+      number: 0
+      mode:
+        output: true
+      inverted: false
+  - platform: gpio
+    name: "MCP23017_1 Pin A0"
+    pin:
+      mcp23xxx: mcp23017_out2
+      number: 0
+      mode:
+        output: true
+      inverted: false
+  - platform: gpio
+    name: "MCP23017_2 Pin A0"
+    pin:
+      mcp23xxx: mcp23017_out3
+      number: 0
+      mode:
+        output: true
+      inverted: false
+  - platform: gpio
+    name: "MCP23017_3 Pin A0"
+    pin:
+      mcp23xxx: mcp23017_out4
+      number: 0
+      mode:
+        output: true
+      inverted: false
+
+# # Individual inputs
+binary_sensor:
+  - platform: gpio
+    id: internal_button
+    pin:
+      number: GPIO4
+      mode:
+        input: true
+        pullup: true
+      inverted: true
+    filters:
+      - delayed_on: 10ms
+    on_press:
+      then:
+        - display.page.show_next: my_display
+#     name: "MCP23017 Pin B7"
+#     pin:
+#       mcp23xxx: mcp23017_hub
+#       # Use pin B7
+#       number: 15
+#       # One of INPUT or INPUT_PULLUP
+#       mode:
+#         input: true
+#         pullup: true
+#       inverted: false