add serial_prefix to config

Move uart and modbus to main file
Switch dashboard import to latest branch
2026-04-10 20:50:02 +02:00 · 2024-05-27 20:32:25 +02:00 · 2024-05-23 20:11:00 +02:00 · 2024-05-22 19:37:04 +02:00 · 2024-05-22 17:03:31 +02:00
19 changed files with 327 additions and 79 deletions
--- a/boneio-24x16_switches_v0_5-v0_6.yaml
+++ b/boneio-24x16_switches_v0_5-v0_6.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-24-sw-06
  friendly_name: 'BoneIO ESP 24x16 Switches'
+  serial_prefix: 'esp24' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-24x16_switches_v0_5-v0_6.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-24x16_switches_v0_5-v0_6.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_5-v0_6/display.yaml',
        'devices_v0_5-v0_6/time.yaml',
        'devices_v0_5-v0_6/i2c.yaml',
@@ -40,7 +42,6 @@ packages:
        'devices_v0_5-v0_6/pcf_with_mcp.yaml',
        'boards/24x16_output.yaml',
        # 'devices_v0_5-v0_6/one_wire.yaml',
-        # 'devices_v0_5-v0_6/uart.yaml',
      ]

 logger:
@@ -576,3 +577,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin3_1
+#   rx_pin: GPIO3
+#   tx_pin: GPIO1
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-24x16_switches_v0_7.yaml
+++ b/boneio-24x16_switches_v0_7.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-24-sw-07
  friendly_name: 'BoneIO ESP 24x16 Switches'
+  serial_prefix: 'esp24' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-24x16_switches_v0_7.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-24x16_switches_v0_7.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_7/display.yaml',
        'devices_v0_7/i2c.yaml',
        'devices_v0_7/ina219.yaml',
@@ -39,7 +41,6 @@ packages:
        'devices_v0_7/pcf_with_mcp.yaml',
        'boards/24x16_output.yaml',
        # 'devices_v0_7/one_wire.yaml',
-        # 'devices_v0_7/uart.yaml',
      ]

 logger:
@@ -572,3 +573,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin14_15
+#   rx_pin: GPIO14
+#   tx_pin: GPIO15
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-32x10_lights_v0_5-v0_6.yaml
+++ b/boneio-32x10_lights_v0_5-v0_6.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-32-l-06
  friendly_name: 'BoneIO ESP 32x10 Lights'
+  serial_prefix: 'esp32' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-32x10_lights_v0_5-v0_6.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-32x10_lights_v0_5-v0_6.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_5-v0_6/display.yaml',
        'devices_v0_5-v0_6/time.yaml',
        'devices_v0_5-v0_6/i2c.yaml',
@@ -40,7 +42,6 @@ packages:
        'devices_v0_5-v0_6/pcf.yaml',
        'boards/32x10_output.yaml',
        # 'devices_v0_5-v0_6/one_wire.yaml',
-        # 'devices_v0_5-v0_6/uart.yaml',
      ]

 logger:
@@ -633,3 +634,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin3_1
+#   rx_pin: GPIO3
+#   tx_pin: GPIO1
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-32x10_lights_v0_7.yaml
+++ b/boneio-32x10_lights_v0_7.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-32-l-07
  friendly_name: 'BoneIO ESP 32x10 Lights'
+  serial_prefix: 'esp32' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,33 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-32x10_lights_v0_7.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-32x10_lights_v0_7.yaml@latest
  import_full_config: true

-modbus:
-  send_wait_time: 200ms
-  uart_id: uart_pin14_15
-  id: mod_bus
-
-modbus_controller:
-  - id: sofarsolar
-    address: 0x09
-    modbus_id: mod_bus
-    setup_priority: -10
-    update_interval: 15s
-
 packages:
-  # extra_boneio_package:
-  #   url: github://boneIO-eu/esphome-packages
-  #   file: sofar-inverter-ktl.yaml
-  #   vars:
-  #     sofar_modbus_id: sofarsolar
-
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_7/display.yaml',
        'devices_v0_7/i2c.yaml',
        'devices_v0_7/ina219.yaml',
@@ -57,7 +41,6 @@ packages:
        'devices_v0_7/pcf.yaml',
        'boards/32x10_output.yaml',
        # 'devices_v0_7/one_wire.yaml',
-        'devices_v0_7/uart.yaml',
      ]

 logger:
@@ -647,3 +630,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin14_15
+#   rx_pin: GPIO14
+#   tx_pin: GPIO15
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-32x10_switches_v0_5-v0_6.yaml
+++ b/boneio-32x10_switches_v0_5-v0_6.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-32-sw-06
  friendly_name: 'BoneIO ESP 32x10 Switches'
+  serial_prefix: 'esp32' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-32x10_switches_v0_5-v0_6.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-32x10_switches_v0_5-v0_6.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_5-v0_6/display.yaml',
        'devices_v0_5-v0_6/time.yaml',
        'devices_v0_5-v0_6/i2c.yaml',
@@ -40,7 +42,6 @@ packages:
        'devices_v0_5-v0_6/pcf.yaml',
        'boards/32x10_output.yaml',
        # 'devices_v0_5-v0_6/one_wire.yaml',
-        # 'devices_v0_5-v0_6/uart.yaml',
      ]

 logger:
@@ -632,3 +633,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin3_1
+#   rx_pin: GPIO3
+#   tx_pin: GPIO1
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-32x10_switches_v0_7.yaml
+++ b/boneio-32x10_switches_v0_7.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-32-sw-07
  friendly_name: 'BoneIO ESP 32x10 Switches'
+  serial_prefix: 'esp32' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-32x10_switches_v0_7.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-32x10_switches_v0_7.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_7/display.yaml',
        'devices_v0_7/i2c.yaml',
        'devices_v0_7/ina219.yaml',
@@ -39,7 +41,6 @@ packages:
        'devices_v0_7/pcf.yaml',
        'boards/32x10_output.yaml',
        # 'devices_v0_7/one_wire.yaml',
-        # 'devices_v0_7/uart.yaml',
      ]

 logger:
@@ -628,3 +629,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin14_15
+#   rx_pin: GPIO14
+#   tx_pin: GPIO15
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-cover_mix_lights_v0_5-v0_6.yaml
+++ b/boneio-cover_mix_lights_v0_5-v0_6.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-cm-l-06
  friendly_name: 'BoneIO ESP Cover Mix Lights'
+  serial_prefix: 'espcm' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-cover_mix_lights_v0_5-v0_6.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-cover_mix_lights_v0_5-v0_6.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_5-v0_6/display.yaml',
        'devices_v0_5-v0_6/time.yaml',
        'devices_v0_5-v0_6/i2c.yaml',
@@ -40,7 +42,6 @@ packages:
        'devices_v0_5-v0_6/pcf.yaml',
        'boards/8_covers_16_output.yaml',
        # 'devices_v0_5-v0_6/one_wire.yaml',
-        # 'devices_v0_5-v0_6/uart.yaml',
      ]

 logger:
@@ -737,3 +738,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin3_1
+#   rx_pin: GPIO3
+#   tx_pin: GPIO1
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-cover_mix_lights_v0_7.yaml
+++ b/boneio-cover_mix_lights_v0_7.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-cm-l-07
  friendly_name: 'BoneIO ESP Cover Mix Lights'
+  serial_prefix: 'espcm' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-cover_mix_lights_v0_7.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-cover_mix_lights_v0_7.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_7/display.yaml',
        'devices_v0_7/i2c.yaml',
        'devices_v0_7/ina219.yaml',
@@ -39,7 +41,6 @@ packages:
        'devices_v0_7/pcf.yaml',
        'boards/8_covers_16_output.yaml',
        # 'devices_v0_7/one_wire.yaml',
-        # 'devices_v0_7/uart.yaml',
      ]

 logger:
@@ -733,3 +734,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin14_15
+#   rx_pin: GPIO14
+#   tx_pin: GPIO15
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-cover_mix_switches_v0_5-v0_6.yaml
+++ b/boneio-cover_mix_switches_v0_5-v0_6.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-cm-sw-06
  friendly_name: 'BoneIO ESP Cover Mix Switches'
+  serial_prefix: 'espcm' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-cover_mix_switches_v0_5-v0_6.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-cover_mix_switches_v0_5-v0_6.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_5-v0_6/display.yaml',
        'devices_v0_5-v0_6/time.yaml',
        'devices_v0_5-v0_6/i2c.yaml',
@@ -40,7 +42,6 @@ packages:
        'devices_v0_5-v0_6/pcf.yaml',
        'boards/8_covers_16_output.yaml',
        # 'devices_v0_7/one_wire.yaml',
-        # 'devices_v0_7/uart.yaml',
      ]

 logger:
@@ -736,3 +737,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin3_1
+#   rx_pin: GPIO3
+#   tx_pin: GPIO1
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-cover_mix_switches_v0_7.yaml
+++ b/boneio-cover_mix_switches_v0_7.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-cm-sw-07
  friendly_name: 'BoneIO ESP Cover Mix Switches'
+  serial_prefix: 'espcm' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-cover_mix_switches_v0_7.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-cover_mix_switches_v0_7.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_7/display.yaml',
        'devices_v0_7/i2c.yaml',
        'devices_v0_7/ina219.yaml',
@@ -39,7 +41,6 @@ packages:
        'devices_v0_7/pcf.yaml',
        'boards/8_covers_16_output.yaml',
        # 'devices_v0_7/one_wire.yaml',
-        # 'devices_v0_7/uart.yaml',
      ]

 logger:
@@ -733,3 +734,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin14_15
+#   rx_pin: GPIO14
+#   tx_pin: GPIO15
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-cover_v0_5-v0_6.yaml
+++ b/boneio-cover_v0_5-v0_6.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-c-06
  friendly_name: 'BoneIO ESP Cover'
+  serial_prefix: 'espc' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-cover_v0_5-v0_6.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-cover_v0_5-v0_6.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_5-v0_6/display.yaml',
        'devices_v0_5-v0_6/time.yaml',
        'devices_v0_5-v0_6/i2c.yaml',
@@ -40,7 +42,6 @@ packages:
        'devices_v0_5-v0_6/pcf.yaml',
        'boards/16_cover_pcf.yaml',
        # 'devices_v0_5-v0_6/one_wire.yaml',
-        # 'devices_v0_5-v0_6/uart.yaml',
      ]

 logger:
@@ -839,3 +840,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin3_1
+#   rx_pin: GPIO3
+#   tx_pin: GPIO1
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-cover_v0_7.yaml
+++ b/boneio-cover_v0_7.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-c-07
  friendly_name: 'BoneIO ESP Cover'
+  serial_prefix: 'espc' #Don't change it.

 esphome:
  name: '${name}'
@@ -23,15 +24,16 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-cover_v0_7.yaml@v1.0.5
+  package_import_url: github://boneIO-eu/esphome/boneio-cover_v0_7.yaml@latest
  import_full_config: true

 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.5
+    ref: v1.0.16
    files: [
        'devices/buzzer.yaml',
+        'devices/serial_no.yaml',
        'devices_v0_7/display.yaml',
        'devices_v0_7/i2c.yaml',
        'devices_v0_7/ina219.yaml',
@@ -39,7 +41,6 @@ packages:
        'devices_v0_7/pcf.yaml',
        'boards/16_cover_pcf.yaml',
        # 'devices_v0_7/one_wire.yaml',
-        # 'devices_v0_7/uart.yaml',
      ]

 logger:
@@ -835,3 +836,25 @@ binary_sensor:
      mode:
        input: true
      inverted: true
+######################
+### MODBUS SECTION ###
+######################
+# UNCOMMENT BELOW TO USE MODBUS
+# uart:
+#   id: uart_pin14_15
+#   rx_pin: GPIO14
+#   tx_pin: GPIO15
+#   baud_rate: 9600
+#   stop_bits: 1
+
+# modbus:
+#   send_wait_time: 200ms
+#   uart_id: uart_pin14_15
+#   id: boneio_modbus
+
+# modbus_controller:
+#   - id: YOURDEVICE ID
+#     address: 0x09
+#     modbus_id: mod_bus
+#     setup_priority: -10
+#     update_interval: 60s
--- a/boneio-dimmer_2rgbw-v0_3.yaml
+++ b/boneio-dimmer_2rgbw-v0_3.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-dr-rgbw-03
  friendly_name: 'BoneIO Dimmer LED'
+  serial_prefix: 'dim' #Don't change it.

 esphome:
  name: '${name}'
@@ -20,10 +21,10 @@ external_components:
 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.13
+    ref: v1.0.16
    files:
      [
-        'devices/dimmer_serial_no.yaml',
+        'devices/serial_no.yaml',
        'devices/dimmer_i2c.yaml',
        'devices/dimmer_ina219.yaml',
      ]
@@ -38,7 +39,7 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-dimmer_2rgbw-v0_3.yaml@v1.0.13
+  package_import_url: github://boneIO-eu/esphome/boneio-dimmer_2rgbw-v0_3.yaml@latest
  import_full_config: true

 pcf8574:
--- a/boneio-dimmer_4cct-v0_3.yaml
+++ b/boneio-dimmer_4cct-v0_3.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-dr-4cct-03
  friendly_name: 'BoneIO Dimmer LED'
+  serial_prefix: 'dim' #Don't change it.

 esphome:
  name: '${name}'
@@ -20,10 +21,10 @@ external_components:
 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.12
+    ref: v1.0.16
    files:
      [
-        'devices/dimmer_serial_no.yaml',
+        'devices/serial_no.yaml',
        'devices/dimmer_i2c.yaml',
        'devices/dimmer_ina219.yaml',
      ]
@@ -38,7 +39,7 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-dimmer_4cct-v0_3.yaml@v1.0.12
+  package_import_url: github://boneIO-eu/esphome/boneio-dimmer_4cct-v0_3.yaml@latest
  import_full_config: true

 pcf8574:
--- a/boneio-dimmer_8ch-v0_3.yaml
+++ b/boneio-dimmer_8ch-v0_3.yaml
@@ -1,6 +1,7 @@
 substitutions:
  name: boneio-dr-8ch-03
  friendly_name: 'BoneIO Dimmer LED'
+  serial_prefix: 'dim' #Don't change it.

 esphome:
  name: '${name}'
@@ -20,10 +21,10 @@ external_components:
 packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
-    ref: v1.0.12
+    ref: v1.0.16
    files:
      [
-        'devices/dimmer_serial_no.yaml',
+        'devices/serial_no.yaml',
        'devices/dimmer_i2c.yaml',
        'devices/dimmer_ina219.yaml',
      ]
@@ -38,7 +39,7 @@ ethernet:
  power_pin: GPIO16

 dashboard_import:
-  package_import_url: github://boneIO-eu/esphome/boneio-dimmer_8ch-v0_3.yaml@v1.0.12
+  package_import_url: github://boneIO-eu/esphome/boneio-dimmer_8ch-v0_3.yaml@latest
  import_full_config: true

 pcf8574:
--- a/devices/dimmer_serial_no.yaml
+++ b/devices/dimmer_serial_no.yaml
@@ -3,7 +3,7 @@ text_sensor:
    name: 'Serial No.'
    lambda: |-
      std::string mac = get_mac_address();
-      return "dim" + mac.erase(0, mac.length()/2);
+      return to_string("${serial_prefix}") + mac.erase(0, mac.length()/2);
    icon: mdi:expansion-card-variant
    entity_category: diagnostic
-    update_interval: 10min
+    update_interval: 60min
--- a/devices_v0_5-v0_6/uart.yaml
+++ b/devices_v0_5-v0_6/uart.yaml
@@ -1,6 +0,0 @@
-uart:
-  id: uart_pin3_1
-  rx_pin: GPIO3
-  tx_pin: GPIO1
-  baud_rate: 9600
-  stop_bits: 1
--- a/devices_v0_7/one_wire.yaml
+++ b/devices_v0_7/one_wire.yaml
@@ -1,6 +1,5 @@
 dallas:
- pin: GPIO32
-
+  - pin: GPIO32
 # sensor:
 #   - platform: dallas
 #     address: 0x283c01d607d4df28
--- a/devices_v0_7/uart.yaml
+++ b/devices_v0_7/uart.yaml
@@ -1,6 +0,0 @@
-uart:
-  id: uart_pin14_15
-  rx_pin: GPIO14
-  tx_pin: GPIO15
-  baud_rate: 9600
-  stop_bits: 1
Author	SHA1	Message	Date
pszafer	206a1912f2	add serial_prefix to config	2024-05-27 20:32:25 +02:00
pszafer	8412fb6fe5	Move uart and modbus to main file	2024-05-23 20:11:00 +02:00
pszafer	1befa8554a	Switch dashboard import to latest branch	2024-05-22 19:37:04 +02:00
pszafer	3741466e05	fix fw	2024-05-22 17:03:31 +02:00