substitutions:
  devicename: wt32
  
esphome:
  name: ${devicename}
  platform: ESP32
  board: esp-wrover-kit
  on_boot:
    then:
      ds1307.read_time:


ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO0_IN
  phy_addr: 1
  power_pin: GPIO16
  id: eth

external_components:
  - source: github://ell249/esphome-PCT2075@master
    components: [ pct2075 ]
  - source: github://btomala/esphome-LM75@v1
    components: [ lm75 ]

font:
  - file: "fonts/DejaVuSans.ttf"
    id: fontSmall
    size: 9
  - file: "fonts/danube__.ttf"
    id: danube
    size: 15

logger:
  level: DEBUG
  baud_rate: 0 #Important. You can't use serial port

api:
ota:

web_server:
  port: 80

i2c:
  - id: bus_b
    sda: 14
    scl: 15
    scan: true

time:
  - platform: ds1307
    update_interval: never
  - platform: homeassistant
    on_time_sync:
      then:
        ds1307.write_time:


display:
  - platform: ssd1306_i2c
    model: "SH1106 128x64"
    address: 0x3C
    id: my_display
    pages:
      - id: page1
        lambda: |-
          it.print(3, 3, id(danube), "bone");
          it.print(53, 3, id(danube), "iO");
          it.print(3, 22, id(fontSmall), "Host: ${devicename}");
          int seconds = round(id(uptime_sensor).raw_state);
          int days = seconds / (24 * 3600);
          seconds = seconds % (24 * 3600);
          int hours = seconds / 3600;
          seconds = seconds % 3600;
          int minutes = seconds /  60;
          seconds = seconds % 60;
          it.printf(3, 32, id(fontSmall), "IP Address: 192.168.1.1");
          it.printf(3, 42, id(fontSmall), "Uptime: %s", (
            (days ? to_string(days) + "d " : "") +
            (hours ? to_string(hours) + "h " : "") +
            (minutes ? to_string(minutes) + "m " : "") +
            (to_string(seconds) + "s")
          ).c_str());
      - id: page2
        lambda: |-
          it.printf(0, 0, id(fontSmall), "MCP1_1: %s", id(switch_mcp_out1_1).state ? "ON" : "OFF");
          it.print(0, 10, id(fontSmall), "This is page 2!");
sensor:
  - platform: mcp9808
    name: "Living Room Temperature"
    update_interval: 60s
  - platform: uptime
    id: uptime_sensor
  - platform: lm75
    id: temperature
    name: "Board temperature measurement"
    update_interval: 60s
    address: 0x48
# sensor:
          # it.printf(3, 32, id(fontSmall), "Wi-Fi: %.1s", id(eth).state);
#   - platform: pct2075
#     address: 0x18
#     temperature:
#       name: "PCT2075 Temperature"
#     update_interval: 30s


mcp23017:
  - id: 'mcp23017_out1'
    address: 0x20
  - id: 'mcp23017_out2'
    address: 0x21
  - id: 'mcp23017_out3'
    address: 0x22
  - id: 'mcp23017_out4'
    address: 0x23

# # Individual outputs
switch:
  - platform: gpio
    id: switch_mcp_out1_1
    name: "MCP23017 Pin A0"
    pin:
      mcp23xxx: mcp23017_out1
      number: 0
      mode:
        output: true
      inverted: false
  - platform: gpio
    name: "MCP23017_1 Pin A0"
    pin:
      mcp23xxx: mcp23017_out2
      number: 0
      mode:
        output: true
      inverted: false

# # Individual inputs
binary_sensor:
  - platform: gpio
    id: internal_button
    pin:
      number: GPIO4
      mode:
        input: true
        pullup: true
      inverted: true
    filters:
      - delayed_on: 10ms
    on_press:
      then:
        - display.page.show_next: my_display
  - platform: gpio
    id: binary_sensor1
    name: "MCP23017 Pin A0"
    pin:
      mcp23xxx: mcp23017_out4
      number: 0
      mode:
        output: false
      inverted: false
    on_multi_click:
    - timing:
        - ON for at most 1s
        - OFF for at most 0.3s
        - ON for at most 1s
        - OFF for at least 0.2s
      then:
        - switch.turn_on: switch_mcp_out1_1
        - logger.log: "Double-Clicked"
    - timing:
        - ON for at most 1s
        - OFF for at least 0.5s
      then:
        - switch.toggle: switch_mcp_out1_1
        - logger.log: "Single-Clicked"
#     name: "MCP23017 Pin B7"
#     pin:
#       mcp23xxx: mcp23017_hub
#       # Use pin B7
#       number: 15
#       # One of INPUT or INPUT_PULLUP
#       mode:
#         input: true
#         pullup: true
#       inverted: false