esphome/dev-boneio-ps01.yaml

substitutions:
  name: boneio-ps-01
  friendly_name: 'BoneIO PS-01 Czujnik Obecności'
  serial_prefix: 'ps01' #Don't change it.
  firmware_manifest: 'https://boneio.eu/esp/boneio-ps-01.json' # URL manifestu

esphome:
  name: '${name}'
  friendly_name: '${friendly_name}'
  name_add_mac_suffix: true
  project:
    name: boneio.presence-sensor-ps01
    version: 'dev0.1' # Przykładowa wersja
  on_boot:
    priority: -100
    then:
      - delay: 5s
      - if:
          condition:
            lambda: 'return id(serial_no) != nullptr;'
          then:
            - component.update: serial_no
            - logger.log: "Serial No updated on boot"
          else:
            - logger.log: "Serial No component not found"

esp32:
  variant: esp32s3
  flash_size: 16MB
  framework:
    type: esp-idf
psram:
  mode: octal
  speed: 80MHz
# --- NOWA SEKCJA: WiFi ---
wifi:
  ssid: "TwojeSSID"
  password: "TwojeHaslo"
  
  # Tryb AP do pierwszej konfiguracji
  ap:
    ssid: "PS-01 Sensor Setup"
    password: "boneio-setup"

captive_portal:


i2c:
  id: i2c_bus # Dodano ID dla czujników
  sda: GPIO10
  scl: GPIO11
  scan: True
  frequency: 400kHz

# --- ZAKTUALIZOWANY UART (dla radaru) ---
uart:
  - id: radar_uart
    tx_pin: GPIO21 # ESP TX -> Radar RX
    rx_pin: GPIO14 # ESP RX -> Radar TX
    baud_rate: 115200 # Standard dla LD2412
  - id: boneio_uart
    rx_pin: GPIO47 # CAN RX wg tabeli (dla CAN Bus)
    tx_pin: GPIO48 # CAN TX wg tabeli (dla CAN Bus)
    baud_rate: 9600
    stop_bits: 1

# --- NOWA SEKCJA: Radar LD2412 ---
ld2412:
  uart_id: radar_uart

packages:
  internals_packages:
    url: https://github.com/boneIO-eu/esphome
    ref: packages-v1.7.2
    files: [
        'devices/serial_no.yaml',
      ]

dashboard_import:
  package_import_url: github://boneIO-eu/esphome/boneio-ps-01-presence-sensor.yaml@main # Zgadywany URL
  import_full_config: true

# --- USUNIĘTY pcf8574 ---

logger:
  hardware_uart: UART0
api:
  reboot_timeout: 0s
ota:
  - platform: esphome
  - platform: web_server

web_server:
  port: 80
  version: 3
  local: true

# --- USUNIĘTE 'output' i 'light' ---

debug:
  update_interval: 15s

sensor:
  - platform: lm75b
    id: boneIO_temp
    name: 'Temperature'
    update_interval: 30s
    entity_category: diagnostic
    on_value_range:
      - above: 70.0
        then:
          - switch.turn_on: buzzer
      - below: 70.0
        then:
          - switch.turn_off: buzzer
  - platform: debug
    free:
      name: "Heap Free"
    block:
      name: "Heap Max Block"
  
  # --- NOWA SEKCJA: Czujniki I2C ---
  - platform: sht4x
    i2c_id: i2c_bus
    address: 0x44 # Z tabeli
    temperature:
      name: "Temperatura"
    humidity:
      name: "Wilgotność"
    update_interval: 15s
  
  - platform: veml7700
    address: 0x10
    update_interval: 60s

    # short variant of sensor definition:
    ambient_light: "Ambient light"
    # longer variant of sensor definition:
    actual_gain:
      name: "Actual gain"

  # Czujniki dla radaru LD2412 (dystans, energia)
  # zostaną dodane automatycznie przez komponent 'ld2412'

switch:
  - platform: gpio
    id: buzzer
    name: 'Buzzer'
    pin:
      number: GPIO12 # Zaktualizowany pin
      mode: output
      inverted: false
  
  - platform: gpio
    id: can_stb
    name: 'CAN STB'
    pin:
      number: GPIO13 # Zaktualizowany pin
      mode: output
      inverted: false

  # --- NOWA SEKCJA: Przełączniki ---
  - platform: gpio
    id: led_status
    name: 'LED Status'
    pin:
      number: GPIO1 # Zaktualizowany pin
      mode: output
      inverted: false

  - platform: gpio
    id: relay_1
    name: 'Przekaźnik 1'
    pin:
      number: GPIO18 # Z tabeli
      mode: output
      inverted: false
  
  - platform: gpio
    id: relay_2
    name: 'Przekaźnik 2'
    pin:
      number: GPIO17 # Z tabeli
      mode: output
      inverted: false


binary_sensor:
  - platform: gpio
    name: 'Obecność (Pin OUT)'
    pin:
      number: GPIO41 # RADAR_OUT
      mode: input
    device_class: presence