starred/esphome
1
0
Fork 0
mirror of https://github.com/boneIO-eu/esphome.git synced 2026-04-10 20:50:02 +02:00
Code Issues Packages Projects Releases 10 Wiki Activity
Files
ae9c3aaf30ff860538a22fa37e3e6b88ac76c790
esphome/dev-boneio-8x10A-adc.yaml
pszafer ae9c3aaf30 fix gpio for 8x10A
2025-11-23 08:52:13 +01:00

355 lines
6.9 KiB
YAML
Raw Blame History

substitutions:
name: boneio-8x10a-cover-dev01
friendly_name: 'BoneIO Relay 8x10A dev0.1'
serial_prefix: 'dim2' #Don't change it.
firmware_manifest: 'https://boneio.eu/esp/boneio-relay-8x10a-cover-dev0.3.json'
esphome:
name: '${name}'
friendly_name: '${friendly_name}'
name_add_mac_suffix: true
project:
name: boneio.relay-8x10a-cover
version: 'dev0.3'
on_boot:
priority: -100
then:
- delay: 5s
- if:
condition:
lambda: 'return id(serial_no) != nullptr;'
then:
- component.update: serial_no
- logger.log: "Serial No updated on boot"
else:
- logger.log: "Serial No component not found"
esp32:
board: esp32-s3-devkitc-1
framework:
type: esp-idf
ethernet:
id: eth
type: W5500
clk_pin: GPIO13
mosi_pin: GPIO39
miso_pin: GPIO38
cs_pin: GPIO12
interrupt_pin: GPIO2
reset_pin: GPIO1
clock_speed: 25MHz
external_components:
- source: github://boneIO-eu/esphome-LM75@main #Original source and thank you note for BTomala https://github.com/boneIO-eu/esphome-lm75
components: [lm75]
i2c:
sda: GPIO10
scl: GPIO11
scan: True
frequency: 400kHz
uart:
id: boneio_uart
rx_pin: GPIO21
tx_pin: GPIO14
baud_rate: 9600
stop_bits: 1
spi:
- id: spi_ade7953
mosi_pin: GPIO35
miso_pin: GPIO37
clk_pin: GPIO36
modbus:
send_wait_time: 80ms
uart_id: boneio_uart
id: boneio_modbus
packages:
internals_packages:
url: https://github.com/boneIO-eu/esphome
ref: v1.7.1
files: [
'devices/serial_no.yaml',
]
boneiopackages:
url: https://github.com/boneIO-eu/esphome_packages
ref: main
refresh: 1min
files:
- path: sdm630.yaml
dashboard_import:
package_import_url: github://boneIO-eu/esphome/boneio-relay-8x10a-cover-dev0.3.yaml@main
import_full_config: true
pcf8574:
- id: 'pcf_inputs'
address: 0x38
logger:
hardware_uart: UART0
api:
reboot_timeout: 0s
ota:
- platform: esphome
- platform: web_server
# update:
# - id: update_std
# platform: http_request
# name: boneIO FW Update
# update_interval: 3 minutes
# source: ${firmware_manifest}
web_server:
port: 80
version: 3
local: true
debug:
update_interval: 15s
sensor:
- platform: debug
free:
name: "Heap Free"
block:
name: "Heap Max Block"
loop_time:
name: "Loop Time"
- platform: lm75
id: boneIO_temp
name: 'Temperature'
update_interval: 30s
entity_category: diagnostic
on_value_range:
- above: 70.0
then:
- switch.turn_on: buzzer
- below: 70.0
then:
- switch.turn_off: buzzer
- platform: ade7953_spi
spi_id: spi_ade7953
cs_pin: GPIO40
irq_pin: GPIO15
update_interval: 10s
voltage:
name: "ADE7953 1 Voltage"
current_a:
name: "ADE7953 1 Current"
- platform: ade7953_spi
spi_id: spi_ade7953
cs_pin: GPIO41
irq_pin: GPIO16
update_interval: 10s
voltage:
name: "ADE7953 2 Voltage"
current_a:
name: "ADE7953 2 Current"
- platform: ade7953_spi
spi_id: spi_ade7953
cs_pin: GPIO42
irq_pin: GPIO17
update_interval: 10s
voltage:
name: "ADE7953 3 Voltage"
current_a:
name: "ADE7953 3 Current"
- platform: ade7953_spi
spi_id: spi_ade7953
cs_pin: GPIO45
irq_pin: GPIO18
update_interval: 10s
voltage:
name: "ADE7953 4 Voltage"
current_a:
name: "ADE7953 4 Current"
switch:
- platform: gpio
id: buzzer
name: 'Buzzer'
pin:
number: GPIO9
mode:
output: true
inverted: false
# *** POCZĄTEK AKTUALIZACJI ***
- platform: gpio
id: can_stb # Poprzednio id: can_bus_switch
name: 'CAN STB' # Poprzednio name: 'CAN Bus Switch'
pin:
number: GPIO20 # Pin dla CAN_STB
mode:
output: true
inverted: false
- platform: gpio
id: can_led
name: 'CAN LED'
pin:
number: GPIO8 # Pin dla CAN_LED
mode:
output: true
inverted: false
# *** KONIEC AKTUALIZACJI ***
- platform: gpio
name: "CAN RX"
pin: GPIO47
- platform: gpio
name: "CAN TX"
pin: GPIO48
# Przełączniki dla linii RST układów ADE7953
- platform: gpio
name: "ADE7953 RST 1"
pin: GPIO4
- platform: gpio
name: "ADE7953 RST 2"
pin: GPIO5
- platform: gpio
name: "ADE7953 RST 3"
pin: GPIO6
- platform: gpio
name: "ADE7953 RST 4"
pin: GPIO7
# !!! BRAKUJĄCA SEKCJA !!!
# Musisz tutaj dodać definicje dla 8 przekaźników.
# Na przykład:
# - platform: gpio
# name: "Relay 1"
# pin: GPIO_PIN_PRZEKAŹNIKA_1
# - platform: gpio
# name: "Relay 2"
# pin: GPIO_PIN_PRZEKAŹNIKA_2
# ... i tak 8 razy
binary_sensor:
- platform: gpio
name: 'IN_01'
id: in_01
pin:
pcf8574: pcf_inputs
number: 0
mode:
input: true
inverted: true
- platform: gpio
name: 'IN_02'
id: in_02
pin:
pcf8574: pcf_inputs
number: 1
mode:
input: true
inverted: true
- platform: gpio
name: 'IN_03'
id: in_03
pin:
pcf8574: pcf_inputs
number: 2
mode:
input: true
inverted: true
- platform: gpio
name: 'IN_04'
id: in_04
pin:
pcf8574: pcf_inputs
number: 3
mode:
input: true
inverted: true
- platform: gpio
name: 'IN_05'
id: in_05
pin:
pcf8574: pcf_inputs
number: 4
mode:
input: true
inverted: true
- platform: gpio
name: 'IN_06'
id: in_06
pin:
pcf8574: pcf_inputs
number: 5
mode:
input: true
inverted: true
- platform: gpio
name: 'IN_07'
id: in_07
pin:
pcf8574: pcf_inputs
number: 6
mode:
input: true
inverted: true
- platform: gpio
name: 'IN_08'
id: in_08
pin:
pcf8574: pcf_inputs
number: 7
mode:
input: true
inverted: true
- platform: template
name: CAN Bus Button
id: can_bus_button
# canbus:
# - platform: esp32_can
# tx_pin: GPIO48
# rx_pin: GPIO47
# can_id: 4
# bit_rate: 50kbps
# on_frame:
# - can_id: 5
# then:
# - lambda: |-
# if(x.size() > 0) {
# switch(x[0]) {
# case 0x12: // button release
# id(can_bus_button).publish_state(false);
# break;
# case 0x11: // button press
# id(can_bus_button).publish_state(true);
# break;
# }
# }
# button:
# - platform: template
# name: 'CAN Sensor ON'
# on_press:
# - logger.log: Button Pressed
# - canbus.send: [0x11, 0x22, 0x33]
# - platform: template
# name: 'CAN Sensor OFF'
# on_press:
# - logger.log: Button Pressed
# - canbus.send: [0x12, 0x22, 0x33]
Reference in New Issue View Git Blame Copy Permalink